Common Electrical Hazards You Should Know

It is quite easy to tape up a defective wire and think that it would work perfectly again. Maybe it will, but there are high chances that the same wire will become faulty again and it can lead to a short circuit and even a fire in the house. You never know when electrical hazards can happen because there are lots of things that are around you that can cause these outbreaks. So, here are some of the most electrical hazards that can take place in your house or at the workplace and you should be aware of them to avoid an accident:

1. Electrical outlets close to the water unit

This is common for both homes and offices. There should not be any electrical outlet close to a water source. Be it a plug point or a switch or anything, you should strictly avoid the installation of any electrical outlet in the kitchen or in the bathroom. Water is a good conductor of electricity and you have no idea when the water can reach that outlet and create a massacre.

2. Improper grounding

If your office has a lot of electrical gadgets working together like ACs, computers, inverters, and many such items, then make sure that there is proper grounding for everything. There have been cases where people have been electrocuted because there was no grounding of the electrical units. Another reason why grounding is so important is that it allows all the units to be safe when there is a fluctuation in the voltage. You will find that there is a metallic ground pin that controls the voltage. Do not remove that pin because it can nullify the grounding totally.

3. Pouring water when there is a fire due to short circuit

Short circuits can happen when you don’t have a good fuse installed in the house or at the office. If you are using an old fuse, it may not be able to control the flow of electricity and as a result, there can be sparks that lead to a fire. Most family members will be scared to go near the area of a short circuit but there should be a standing instruction for everyone �” no one should pour water into that water to make sure that it comes under control. Pouring water into a fire that has been caused due to the short circuit can only aggravate the situation. Ideally, you should use a fire extinguisher for such cases or call the professionals to handle the fire.

4. Keeping defective wiring unattended

As mentioned above, defective wiring can be taped up temporarily but they have to be changed as soon as possible. Most of the electrical hazards are caused because of poor wiring. It leads to an improper flow of electricity. This is one of the most common electrical hazards that can pose a big threat to you and your family.

It is always better to be safe than sorry. You shouldn’t take any chances with electrical units because the hazards that follow can be uncontrollable.

Ensure Safety In a Home By Avoiding Electrical Hazards

The electrical system installed in any living or working space will have voltages that can be hazardous when people are exposed to them. These electrical hazards must be anticipated and we must see that action is taken to prevent them from happening.

To start with, before you move into a new or previously owned home, it can make sense to have all the circuits tested, broken or missing wall plates replaced, and proper circuit breakers that interrupt ground faults installed, especially for circuits that have outlets in areas where water is used, like bathrooms, kitchens, and laundries.

You must also have a proper knowledge of the main switches and breakers that control all the circuits in your electrical system, as one of the first things that must be done to avoid electrical hazards connected with faulty wiring, switches, and appliances is to switch off the power before you take any action to repair the fault. If your main panel has fuses, it can do no harm to remove the fuses before calling in a qualified and experienced electrician to deal with the problem.

Defective appliances can often become electrical hazards, and if they are not working, have them seen to, by qualified and knowledgeable electricians. Continuing to use an appliance that is not working as it should, will often become an electrical hazard. Lamps that are flickering, or plug points that show sparks can turn into dangerous devices that best attended to immediately.

Power cords must run freely and not be under strain or under furniture or carpets, as walking on them can lead to their damage and make them a source of danger. Do not overload any plug point by using too many devices from a single outlet with adapters and the like, as this can overload the circuit and cause overheating that leads to fire or blown fuses. Check your power cords at regular intervals for frayed wires or loose connections. Read ratings of all electrical gadgets that you use and see that any adapters or other devices you use are of the correct capacity.

Other electrical hazards can come from drilling into walls for hanging wall decor, especially where you have concealed cabling. You can avoid danger from electrical hazards if you make it a practice to always unplug equipment when it is not in use. This is especially important for those devices that are close to sources of water. If any appliance is not working, make sure that you unplug it from the electrical outlet, before you open it to check for the source of the problem.

Faulty wiring or appliances will give warning signals like constantly blown fuses and tripping circuit breakers, and while replacing the fuse or resetting the breaker can get your appliance working once again, it does point to some problem that is better attended to before it becomes a hazard. A constant flickering of lights can point to loose connections. A burning smell from an electrical outlet can point to overload